高泉背斜地层压力测井多参数综合解释与异常高压成因

目前国内外地层压力测井解释方法较多,但大多数方法基于欠压实沉积理论并局限于单一的地层岩性,尤其是针对盆地边缘山前深层构造,单一测井参数确定地层压力误差较大,且无法解释沉积压实机制以外的异常高压。为此,将多种异常高压机制相关的测井参数进行综合解释,建立适合山前复杂构造的地层压力测井多参数计算模型,评价准噶尔盆地南缘高泉背斜高探1井的地层压力剖面,其计算结果与钻井实测数据吻合,相对误差小于3.00%.同时,基于原始沉积加载—卸载过程力学原理,利用地层压力测井多参数分析判别出高泉背斜深层各层系异常高压的形成机制。     

Design and characteristics of a new type laminar plasma torch for materials processing

Laminar plasma jet(LPJ) generated by laminar plasma torch(LPT) has a favorable temperature and velocity distribution. Thus, it is superior to the turbulent plasma jet in material processing.However, most of the reported LPTs usually operate at a relatively low output power with a relatively low arc voltage and thermal efficiency, which limits its capabilities. In this context, this paper attempts to design a new type of high-power LPT with a relatively low arc current and a high thermal efficiency. In the first section, the design principle of the main components is studied and discussed in detail, and a new high-power LPT is proposed. Then, the experimental characteristics of the proposed high-power LPT are examined. Experimental results reveal the following characteristics of the proposed LPT.(1) The max jet length of the proposed LPT reaches at 540 mm.(2) Its mean arc voltage is higher than 290 V when the LPT works with arc currents lower than 200 A, leading to an output power greater than 50 kW.(3) The mean thermal efficiency is higher than 50%. Lastly, the proposed LPT has been applied to spheroidize the aluminum oxide powers. The experiment results for the production of spherical powders show that the proposed LPT has a good characteristic for material processing.     

How does a bank's involvement interplay with a firm's capacity investment? An analysis and comparison of different consortium structures

As nonrecourse project finance (rather than financing on a sovereign basis) is becoming more prevalent worldwide, financing institutions have to collaborate more closely with firms to optimize capacity‐investment and financing decisions. Under this background, this paper presents a stylized Stackelberg games model, taking into account the firm's capacity investment as well as the bank's interest rate and funding ratio decisions. Consortium structures between bank and firm are formalized into five modes based on industry practice, namely, the integrated consortium, pure shareholder funding, bank as leader, full coordination, and bank as follower. The optimality and equilibrium of each of the five modes are analytically derived, and their existence and uniqueness are demonstrated. Valuable economic insights are obtained through both modeling analysis and numerical experiments, with the main findings including the following: (i) a lack of bank financing leads to insufficient capacity investment and poor consortium performance; (ii) interest rate and funding ratio play important but different roles in the bank's risk management; (iii) the bank's proactivity in leading and coordinating the consortium is critical for the two parties’ overall performance; and (iv) if the bank is the follower, the firm's capacity decision is irrelevant to the bank's loan contract, and the consortium cannot be coordinated to the first‐best level of performance.     

New ways to improve the damping properties in high‐performance thermoplastic vulcanizates

The incorporation of viscoelastic materials represents an effective strategy to reduce the vibratory level of structural components. Thermoplastic vulcanizates (TPVs) are a special type of viscoelastic material that combines the elastomeric properties of rubbers with the easy processing of thermoplastics. In the present work, we propose innovative ways to improve the damping properties of high‐performance TPVs by using rubbers with carboxylic functionalities. For that, TPVs from physical blends of carboxylated hydrogenated acrylonitrile butadiene rubber (XHNBR) and polyamide 6 (PA6) were prepared. The chain dynamics of different mixed crosslink systems containing peroxide, metal oxides and hindered phenolic antioxidants were investigated in order to find the most suitable strategy to design a high‐performance TPV system with upgraded damping properties. The results indicate that the damping performance of the TPV system can be tailored by controlling the type and magnitude of the bonding interactions between the mixed crosslink system and the XHNBR rubber phase. Therefore, this study demonstrates the potential of TPV systems containing carboxylic rubbers as high‐performance damping materials. © 2020 Society of Chemical Industry     

Highly efficient chemical mechanical polishing method for SiC substrates using enhanced slurry containing bubbles of ozone gas

In this study, a highly efficient method for chemical mechanical polishing (CMP) of silicon carbide (SiC) substrates using enhanced slurry was proposed and developed. The enhanced slurry contains bubbles of ozone gas generated by ozone gas generator in pure water mixed with a conventional commercially available slurry. Therefore, the enhanced slurry has an oxidizing effect on the Si-face of SiC substrates. To confirm the effectiveness of bubbles enclosing ozone gas, both nano-indentation test and X-ray photoelectron spectroscopy (XPS) analysis were conducted. As a result, the hardness decrease of the Si-face of the SiC substrate was confirmed through the nano-indentation test, and the generation of reaction products was confirmed on Si-face of SiC substrate in the XPS analysis. According to a series of experimental results of our proposed highly efficient CMP method for SiC substrates, the removal rate can be increased when the enhanced slurry was applied, comparing with that for the not only conventional commercially available slurry but also commercially available dedicated slurry.     

朝凯煤矿露天台阶爆破装药结构优化应用研究

本文以神达朝凯煤矿正在开采的台阶为工程背景,针对该矿在台阶爆破过程中存在着大块率高、根底多的现象,通过改变装药结构的方式对爆破参数进行优化。实践证明,优化后大块率和根底问题的治理效果明显。     

Inhibition of stress corrosion cracking in 304 stainless steel through titanium ion implantation

The effects of titanium ion implantation on the stress corrosion cracking (SCC) behaviour of 304 austenitic stainless steel were studied. Slow strain rate tests (SSRTs) were conducted on 304 steel in air and in 5?wt-% NaCl solution. The microscopic effects of ion implantation were evaluated by Stopping and Range of Ions in Matter Procedures (SRIM). Fracture morphologies and microstructures were investigated by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The fracture surfaces illustrate that ion implantation significantly inhibits the corrosion pits that initiate SCC. A dense passive film, which inhibits SCC, was formed during the ion implantation process. SCC initiation was restrained due to the dense dislocation nets that were generated by titanium ion implantation.

Highlights

• Ion implantation inhibits SCC susceptibility.

• The lack of Cr at the grain boundary leads to the expansion of SCC along the grain boundary.

• Implantation-induced damage leads to high-density dislocations.

• The surface was amorphised due to high-density dislocations.

     

载铜树脂处理高含盐氨氮废水的性能

针对高含盐氨氮废水，选择具有不同功能基团的树脂为载体，进行负载Cu2+改性制得载铜树脂并对其处理高含盐氨氮废水的性能进行研究。在筛选出最佳载铜树脂的基础上，研究pH及Na+浓度、树脂投加量、反应时间对载铜树脂处理高含盐氨氮废水效果的影响，通过对吸附氨氮前后的载铜树脂进行SEM和EDS表征分析并构建吸附动力学模型以进一步探究配位吸附的过程。结果表明，Cu2+可与螯合树脂D751稳定结合且在宽pH值下均表现出耐盐性和良好的氨氮吸附效果；在室温(25℃)、pH=11及Na+浓度4 g/L、树脂投加量8 g/L、反应时间60 min的条件下，D751载铜树脂对氨氮的去除率为34.8%。D751载铜树脂吸附氨氮后其表面出现明显的晶状结构物质，该物质可能为铜氨络合物。D751载铜树脂对高含盐氨氮的吸附符合准二级动力学模型。     

Cutting parameter optimization for one-step shaft excavation technique based on parallel cutting method

The outcome of the cutting blasting in a one-step shaft excavation is heavily related to the cutting parameters used for parallel cutting method. In this study, the relationships between the cutting parameters (such as the hole spacing L and the empty hole diameter D) and damage zones were investigated by numerical simulation. A damage state index γ was introduced and used to characterize the crushing and crack damage zones through a user-defined subroutine. Two indices, i.e., η₁ and η₂ that can reflect the cutting performance, were also introduced. The simulation results indicate that an optimal value of L can be obtained so that the η₁ and η₂ can reach their optimal states for the best cutting performance. A larger D results in better cutting performance when the L value maintains its best. In addition, the influences of the loading rate and the in-situ stress on the cutting performance were investigated. It is found that an explosive with a high loading rate is suit for cutting blasting. The propagation direction and the length of the tensile cracks are affected by the direction and the magnitude of the maximum principal stress.